Harbor Freight Tools Automobile Accessories 93229 User Manual

4” RED FLUSH-MOUNT TAIL LIGHT  
4” AMBER FLUSH-MOUNT TAIL LIGHT  
93228  
93229  
ASSEMBLY & OPERATING INSTRUCTIONS  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or  
any artwork contained herein may be reproduced in any shape or form without the  
express written consent of Harbor Freight Tools.  
For technical questions and replacement parts please call 1-800-444-3353.  
9. Do not allow children to play with the Flush Mount Tail Light.  
10. Always check hardware and assembled parts after assembling. All connections should be  
tight and hardware tightened.  
11. Make certain to follow all local laws regarding vehicles and Tail Lights.  
12. Do not cut or rewire any part of the Tail Light.  
13. Make certain the vehicle is turned off before doing any maintenance.  
Warning:  
The warnings, cautions, and instructions discussed in this instruction manual cannot  
cover all possible conditions and situations that may occur. It must be understood by  
the operator that common sense and caution are factors which cannot be built into  
this product, but must be supplied by the operator.  
Unpacking  
When unpacking your 4” Flush-Mount Tail Lights, check to make sure that all parts listed in the parts  
list on page 4 are included. If any parts are missing or broken, please call HARBOR FREIGHT  
TOOLS at 1-800-444-3353.  
Assembly  
Your 4” Flush-mount Tail Lights will require complete installation. It is important that you read the  
entire manual to become familiar with the product BEFORE you install and use the 4” Flush-Mount  
Tail Lights. Before operating this product be sure that you have all parts described in the Parts List  
and Assembly Diagram located on page 4 of this manual. If you do not have experience doing this  
type of electrical work, the job should be done by an automotive service technician.  
1. Make certain that the vehicle’s engine is OFF before doing any maintenance. Proceed with the  
following steps for installing the 4” Flush-mount Tail Lights.  
2. Use a pin connector or inline splice connector (both not included) to connect the Tail Lights to  
your vehicle. When using an inline splice connector, it is not necessary to strip the wires.  
3. Insert two positive wires to the appropriate wires in your vehicle’s lighting system. Insert one  
wire from your vehicle into one channel of the inline splice connector. Insert the wire from the  
Tail Light into the second channel of the inline splice connector. Fold down the tab on the inline  
splice connector to make the connection. Insert the second wire in the same fashion.  
4. Make certain that the black wire is connected to metal on the vehicle to provide a ground.  
SKU 93228 / 93229  
For technical questions please call 1-800-444-3353.  
Page 3  
Installing the Light Bulb  
1. Use a light bulb of the type described on page 2. Gently grasp and twist the Bulb Housing (2)  
and pull it out from the main Tail Light (1) - see Figure 1.  
Figure 1  
Bulb Housing (2)  
2. Line up pins on the light bulb with the grooves on the Bulb Housing (2) and slide the Light Bulb  
into place.  
3. Verify that the Light Bulb is securely in place. Thread the Bulb Housing back into the main Tail  
Light (1).  
Note: When mounting the Tail Lights to a trailer, both the forward amber and the rear red Tail  
Lights are connected to the trailer’s tail light wires.  
4. Once the wires are properly connected, test them before setting the Tail Light in place.  
5. To mount onto a trailer or vehicle, use all three screw holes in the Tail Light Cover to secure it in  
place. Mounting hardware is not included with the Flush-Mount Tail Light. Note that the Amber  
Tail Light is mounted to the front of the vehicle, and the Red Tail Light is to be mounted to the  
rear of the vehicle.  
Parts List  
Part # Description  
Qty.  
1
1
1
2
MainTail Light  
Bulb Housing  
Note: Some parts are listed and shown for illustration purposes only and are not available  
individually as replacement parts.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS  
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES  
ANY REPRESENTATION OR WARRANTY OF ANY KINDTO THE BUYERTHAT HE OR SHE IS QUALIFIED  
TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY  
PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES  
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND  
LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY  
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS  
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTSTHERETO.  
SKU 93228 / 93229  
For technical questions please call 1-800-444-3353.  
Page 4  

Allstar Products Group LLC Automobile Accessories Twist R Plus Class I Vehicular Swing Gate Operator User Manual
Brother HL 5470DWT User Manual
Carrier 50SX024 060 User Manual
Chromalox CAF 6 User Manual
Friedrich Air Conditioner US10B30A User Manual
Friedrich CP05N10A User Manual
Fujitsu Air Conditioner ASU12RLS User Manual
Goodman Mfg 000 12 User Manual
Haier AU142BNAAA User Manual
Human Touch Automobile Accessories human touch massage chair User Manual