Honeywell Mouse HWC BELT WEH QS User Manual

Belt Mount Sled  
Wearable Solution for Dolphin 70e Black  
Quick Start Guide  
Aller à www.honeywellaidc.com pour le français.  
Vai a www.honeywellaidc.com per l'italiano.  
Gehe zu www.honeywellaidc.com für Deutsch.  
Ir a www.honeywellaidc.com para español.  
Para Português, acesse www.honeywellaidc.com.  
Перейти на русскоязычный сайт www.honeywellaidc.com.  
Pro češtinu jdi na www.honeywellaidc.com.  
Pre slovenčinu choď na www.honeywellaidc.com.  
Türkçe için lütfen www.honeywellaidc.com sayfasını ziyaret ediniz.  
Idź na stronę : www.honeywellaidc.com po quick start w języku polskim.  
如要到中国 www.honeywellaidc.com简体。  
www.honeywellaidc.com  
HWC-BELT-WEH-QS Rev A  
12/14  
 
Getting to Know the Belt Mount Sled  
Power Button  
Audio Cable  
End Cap  
Sled  
Lock  
Scan Button  
(not used with  
Back Button  
End Button  
Bluetooth Ring Scanner)  
Home Button  
Send Button  
Front Microphone  
The sled encases theDolphin 70e Black including the touch panel and helps  
protect the terminal from impacts.  
Dolphin 70e Black Features Not Used  
When the Dolphin 70e Black is installed in the belt mounted sled, the following  
features are not available:  
Touch screen display  
Micro-USB port  
Internal scanner.  
 
Removing the Dolphin Black from the Sled  
1. If the audio end cap is used, remove the audio cable.  
To prevent damage to the Dolphin 70e Black always  
unplug the audio cable before removing the end cap.  
2. Slide the lock down to release the  
end cap.  
3. Push up on the right side of the end cap. Do not  
attempt to remove the end cap without opening the  
lock first!  
4. Pull the end cap off of the sled.  
 
5. Slide the Dolphin 70e Black out of the sled.  
Use the notch in the bottom of the sled to  
push the Dolphin 70e Black.  
Removing the Battery  
1. Remove the Dolphin 70e Black from the sled before changing the bat-  
tery.  
2. Place the terminal in Suspend mode by pressing and releasing the  
Power button  
.
3. Perform the steps illustrated below to remove the battery.  
2
3
4
5
1
 
Installing the Battery  
The Dolphin 70e Black model designed for use with the wearable sled uses  
battery part numbers BAT-STANDARD-02 (Li-ion 3.7 V, 6.179 watt hour) and  
BAT-EXTENDED-02 (Li-ion 3.7 V, 12.358 watt hour) manufactured for  
Honeywell International Inc.  
Note: Standard model battery  
and battery door shown.  
2
1
4
3
5
6
We recommend use of Honeywell Li-ion battery packs. Use of any non-  
Honeywell battery may result in damage not covered by the warranty.  
!
 
Turning Power On  
To turn the terminal On, press and release the Power button  
.
Suspend Mode  
Press and release the Power button  
Suspend Mode.  
to toggle the terminal in or out of  
Because the display is hidden in the belt mount sled, observe the backlights  
for the Send, Home, Back and End keys. When the Dolphin 70e Black is on,  
these keys are backlit. If the keys are not backlit, the terminal is Off or in  
Suspend mode.  
Note: You should always place the terminal into Suspend mode before removing  
the battery.  
Pairing the Bluetooth Ring Scanner (Optional)  
Prior to this step, the system administrator must have configured EZ Pairing.  
Pair the Bluetooth Ring Scanner before placing the terminal in the sled.  
1. Touch  
> Power Tools > EZ Pairing.  
2. The EZ Pairing bar code is displayed on  
the screen. If using a 2D imager ring  
scanner, scan the on-screen bar code or  
the bar code label on the back of the  
terminal with the Bluetooth Ring Scanner.  
If using a 1D ring scanner, scan the bar  
code from the label on the back of the terminal.  
3. Listen for the confirmation beeps.  
4. Confirm the scanner is connected by observing the EZ Pairing icon on  
the terminal display. When the icon is green, the scanner is connected .  
If the icon is red, the scanner is not connected. Scan the bar code again.  
 
5. If the scan wedge icon is displayed, scan wedge is running. If the scan  
wedge icon is not displayed, Touch  
> Power Tools > ScanWedge  
NGW. Tap Yes if a message is displayed about continuing without a  
tethered scanner connected.  
EZ Pairing icon  
Scan Wedge NGW icon  
Placing Dolphin 70e Black into the Sled  
1. If the end cap is installed on the  
sled, slide the lock down to release  
the end cap.  
2. Push up on the right side (the side with the lock) of end  
cap. Do not attempt to remove the end cap without  
sliding the lock first!  
 
3. Pull the end cap off the sled.  
4. Make sure the USB door is closed. Rotate the door  
on the right side of the Dolphin 70e Black to close.  
5. Press until the door is flush with the side of the  
terminal.  
6. Slide the Dolphin 70e Black into the sled.  
 
7. Make sure audio jack door is open. Pull the  
rubber door out and rotate the door 180º as  
shown to prevent damage.  
8. Make sure the audio cable is not installed in the end cap.  
9. Slide the end cap straight onto the sled until it clicks in  
place.  
10. Slide the lock closed to secure the end cap.  
 
Attaching the Headset  
1. Make sure the audio jack door is open as shown in the previous section.  
2. Slide the 3.5mm audio connector into the end  
cap.  
3. Attach the quick disconnect end  
of the headset adapter cable to  
the headset’s cable.  
4. Slide the cable ends together until they click.  
Do not twist or bend the connectors.  
 
Attach the Sled to the Belt Clip  
1. Align the sled assembly with the belt clip  
and press on the sled until it latches onto  
the belt clip. Be sure to align tabs on the  
back of sled with the notches on the belt  
clip.  
2. Slide the clip over a belt to wear the assembly.  
 
Technical Assistance  
Contact information for technical support, product service, and repair can be  
User Documentation  
For localized versions of this document, and to download the User’s Guide,  
Limited Warranty  
warranty information.  
Patents  
For patent information, please refer to www.hsmpats.com.  
Disclaimer  
Honeywell International Inc. (“HII”) reserves the right to make changes in  
specifications and other information contained in this document without prior  
notice, and the reader should in all cases consult HII to determine whether  
any such changes have been made. The information in this publication does  
not represent a commitment on the part of HII.  
HII shall not be liable for technical or editorial errors or omissions contained  
herein; nor for incidental or consequential damages resulting from the  
furnishing, performance, or use of this material.  
This document contains proprietary information that is protected by copyright.  
All rights are reserved. No part of this document may be photocopied,  
reproduced, or translated into another language without the prior written  
consent of HII.  
2014 Honeywell International Inc. All rights reserved.  
 

Haier Dishwasher DW12 PFE2 E User Manual
Haier Washer Dryer XPB50 AS User Manual
Hamilton Beach Toaster 22444 User Manual
Hotpoint Freezer FZA31 User Manual
HP Hewlett Packard Network Router 449298 001 User Manual
HP Hewlett Packard Yard Vacuum 436853 001 User Manual
Ice O Matic Ice Maker IOD 250 User Manual
iHome Home Theater System iDM11 User Manual
iHome MP3 Docking Station IA9 User Manual
Ikelite Camera Accessories A1000 IS User Manual