2-STEP WORK STAND WITH
TOOL TRAY
91174
ASSEMBLY INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
®
©
.
Copyright 2004 by Harbor Freight Tools All rights reserved. No portion
of this manual or any artwork contained herein may be reproduced in any
shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
10. Replacement parts. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
11. Do not operate this product if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment or reflexes
are impaired while taking drugs. If there is any doubt, do not stand upon or try
to assemble this product.
12. Do not exceed the Maximum Weight capacity for either the Steps or the
Tray, mentioned in the Specifications table on page 2.
Caution: Be aware of dynamic loading!
Jumping or bouncing on the Stand may create for a brief instant, an excess
load, which may result in damage to the product and/or personal injury.
Warning:The warnings,cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur.
It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied
by the operator.
Unpacking
When unpacking, check to make sure the following parts are included.
If any parts are missing or broken, please call Harbor Freight Tools at the
number on the cover of this manual.
Assembly Instructions
Note: Assemble on a smooth surface to avoid scratching.
2. Select the Right Leg (4) and Left Leg (7). Attach the Lower Step (5) to the Legs
(4 & 7) (the mounting hole for the Post (3) must be on the Right Leg’s (4) side-
see Figure A) by matching up the holes and securing with Bolts (14), Lock
Washers (17), Washers (16) and Nuts (15). Finger tighten.
3. Attach the Upper Step (6) as in step #2. Tighten all hardware. See Figure A.
Bolt (14)
Upper Step
(6)
Lock Washer (17)
Washer (16)
Nut (15)
This hole must be
here-see Step 2.
Bolt (14)
Lock Washer (17)
Washer (16)
Nut (15)
Lower Step (5)
Right Leg (4)
Left Leg (7)
Figure A
SKU 91174
Page 3
4. Fit the Wheel (8) on the outside of the Left Leg (7) inside the bracket. Position
the Bolt (12) through the bracket on Leg (7), the Wheel (8), and the other side
of the bracket.Tighten with the Nylon Nut (18) on the inside of the Work Stand.
Repeat on the other side of the Leg (7).
See Figure B.
Left Leg (7)
with brackets
Wheel (8)
Bolt (12)
Nylon Nut (18)
Figure B
5. The Post (3) is mounted on the Right Leg (4) with Bolts (12) in the two upper
holes in the Post plate. The Bolt (13) goes in the lower hole. Attach all with
Washers (16), Lock Washers (17) and Nuts (15).
See Figure C .
Tray (1)
Wing
Bolt
(11)
Post (3)
Tool Tray (1)
Bolts (10,
Washers (16)
Lock
Washers (17)
Hand
Grip
(9)
Post
Plate (3)
Extention
Tube (2)
Bolt (12)
Washer (16)
Lock Washer (17)
Nut (15)
Bolt (13)
Pin
Wing Bolt (11)
Washer (16)
Lock Washer (17)
Nut (15)
Figure D
Figure C
6. The Tool Tray (1) needs to be connected to the Extension Tube (2). Use Bolts
(10), Washers (16), and Lock Washers (17) to attach the Tray and tighten all
hardware. See Figure D. Once the ToolTray (1) is connected to the Extension
Tube (2), the Tube can be slipped into the Post (3). Choose the height you want
the Tool Tray at, line up the hole in the Extension Tube (2) to the hole in the Post
(3), tighten the Wing Nut (11), and use the Pin on the Post (3) to lock in position.
See Figures C & D.
Note: Do not place any weight on the Tool Tray (1) unless the Pin is in place.
7. Place Rubber Stoppers (not shown) on the end of each leg.
8. The Handle (9) is used for transporting the Work Station with Tool Tray. Do not
have any objects on the Tray when moving it from one area to another.
SKU 91174
Page 4
Parts List
Part #
Description
Qty.
Part #
Description
Qty.
Tray Bolt
Wing Bolt
Bolt
Bolt
Step Bolt
Nut
Washer
Lock Washer
Nylon Nut
4
1
4
1
6
Tool Tray
Extension Tube
Post
Right Leg
Lower Step
Upper Step
Left Leg
10
11
12
13
14
15
16
17
18
1
1
1
1
1
1
1
2
1
1
2
3
4
5
6
7
8
9
8
12
12
2
3” Wheel
Hand Grip
Assembly Drawing
12
8
1
14
14
7
6
18
16
15
17
8
18
14
12
15
17
16
10
5
16
2
17
14
3
11
12
14
17
15
9
15
16
4
16
17
12
14
13
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE-
MENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.
SKU 91174
Page 5
|