Harbor Freight Tools Dryer Accessories 42986 User Manual

BENCH GRINDER PEDESTAL STAND  
Model 42986  
ASSEMBLY AND OPERATING INSTRUCTIONS  
Read this material before using this product.  
Failure to do so can result in serious injury.  
SAVE THIS MANUAL.  
Copyright© 2000 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein  
may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within  
this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from  
the product described herein. Tools required for assembly and service may not be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
Revised Manual 10l  
 
Before Using  
Before using any tool, any part that appears damaged should be carefully checked to  
determine that it will operate properly and perform its intended function.  
Make sure all Nuts and Bolts are tight.  
Use only Bench Grinders that are fully compatible with the Bench Grinder Pedestal Stand. The Bench Grinder  
Pedestal Stand fits most Harbor Freight Tool Bench Grinders, but you should always check for sure before using.  
Use of the Pedestal Stand is for use with bench grinders only.  
Assembly  
Your Pedestal Stand will require assembly prior to use. It is important that you read the entire manual to  
become familiar with the unit BEFORE you set up the Stand. Before assembling your Stand, be sure that  
you have all parts described in the Parts List and Parts Diagram on the last pages of this manual.  
Set out all parts on a clear work surface prior to assembly.  
Warning:  
Use only bench grinders that are fully compatible with the Bench Grinder Pedestal  
Stand. Using bench grinders which do not fit this stand may result in harm or serious  
injury to the operator. The Bench Grinder Pedestal Stand fits most Harbor Freight  
Tool Bench Grinders, but you should always check for sure before using.  
Use the Pedestal Stand for bench grinders only.  
Step 1)  
Mount the Base (3) to a heavy-duty block of wood which is larger than the Pedestal Stand  
Base, or into cement for safety and stability. A rubber mat should be placed between  
the Base (#3) and the mounting surface to reduce vibration. The Mounting Holes on  
the Base (3) are 3/8” in diameter. Insert appropriate screws (not included) through the  
Base (3) and into a flat and secure surface. The mounting surface must be able to  
support the weight of the Stand as well as the Grinder and work pieces during use.  
Step 2)  
Step 3)  
Insert the Column (#2) into the hole in the Base (3). Insert a Bolt (4) into each  
hole in the Base (3) and tighten them firmly against the Column (2).  
Slide the Work Table (1) into place on top of the Column (2). Thread one Bolt (4) through  
each hole in the WorkTable. Tighten the Bolts (4) until they are firmly against the Column.  
Step 4)  
Step 5)  
Make certain that all Bolts (4) are tightly in place and that the Stand is secure.  
Secure the bench grinder to the Work Table (#1) with six appropriate  
size bolts, washers and nuts (not included).  
Step 6)  
Make sure that the Pedestal Stand and the bench grinder are secure before using.  
SKU 42986  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
Unpacking  
UNPACK AND CHECK CONTENTS  
When unpacking your Bench Grinder Pedestal Stand, check to make sure the following parts are included.  
If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.  
Part  
Description  
Work Table  
Column  
Quantity  
1
2
3
4
1
1
1
4
Base  
Bolt M8 x 24  
Note: Some parts are listed and shown for illustration purposes only  
and are not available individually as replacement parts.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURERAND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL  
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY  
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO  
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS  
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES  
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND  
LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY  
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS  
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
Page 4  
For technical questions, please call 1-800-444-3353.  
SKU 42986  
 

Graco High Chair 3000 User Manual
Grizzly Car Seat H6166 User Manual
Grizzly Grinder T23084 User Manual
Haier CRT Television HTAF21B User Manual
Hasbro Robotics 80703 User Manual
Havis Shields Window WGI F11 User Manual
Health O Meter Scale 2000KL User Manual
Heath Zenith Home Safety Product 3038361 User Manual
hussman Ice Maker 3 User Manual
IBM Laptop GC28 1982 02 User Manual