Harbor Freight Tools Digital Camera 95153 User Manual

OUTDOOR IMITATION CAMERA  
Model 95153  
SET Up INSTRUCTIONS  
Visit our website at: http://www.harborfreight.com  
Read this material before using this product.  
Failure to do so can result in serious injury.  
SAVE ThIS MANUAl.  
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork  
contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight  
Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual  
product may differ slightly from the product described herein. Tools required for assembly and service may not  
be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
Revised Manual 07b, 08a, 09k  
 
9.  
Replacement parts and accessories. When servicing, use only identical replacement  
parts. Use of any other parts will void the warranty. Only use accessories intended for  
use with this product. Approved accessories are available from Harbor Freight Tools.  
10.  
Do not install the Imitation Camera if under the influence of alcohol or drugs.  
Read warning labels if taking prescription medicine to determine if your judgment or  
reflexes are impaired while taking drugs. If there is any doubt, do not install the unit.  
11.  
12.  
For your safety, service and maintenance should be performed regularly by a  
qualified technician.  
The warnings, precautions, and instructions discussed in this instruction manual  
cannot cover all possible conditions and situations that may occur. It must be  
understood by the operator that common sense and caution are factors which  
cannot be built into this product, but must be supplied by the operator.  
SAVE ThESE INSTRUCTIONS.  
UNpACKINg  
When unpacking, check to make sure that the product is intact and undamaged. If any parts  
are missing or broken, please call Harbor Freight Tools at the number on the cover of this  
manual as soon as possible.  
SKU 95153  
For technical questions, please call 1-800-444-3353  
Page 3  
 
ASSEMbly  
Pivoting Screw  
Camera  
Stand (2)  
Wall Bracket (1)  
FIgURE 1  
1.  
Twist the Camera Stand (2) into the Wall Bracket (1). Tilt-up the Pivoting Screw.  
See Figure 1.  
Camera  
Housing (3)  
Pivoting Screw  
Wires (4)  
Camera  
Stand (2)  
FIgURE 2  
2.  
3.  
Screw the Pivoting Screw into the housing of the Camera. Be sure it is secure.  
See Figure 2.  
To make the Camera look more authentic, tuck the Wires (4) into the holes in the  
Camera Stand (2). See Figure 2.  
Note: Turn pivot screw 90° if wall bracket is mounted on a vertical surface.  
SKU 95153  
For technical questions, please call 1-800-444-3353  
Page 4  
 
bATTERy INSTAllATION  
Warning: Only install batteries of the same type and charge level. Replace both  
batteries at once. Install batteries according to polarity markings.  
Sun-Visor (6)  
Battery Case (11)  
Batteries (9)  
Rear Housing (7)  
Battery Cover (8) and Battery Cover Screws (5)  
FIgURE 3  
1.  
Remove the two Battery Cover Screws (5) from the Battery Cover (8) with a screwdriver  
(sold separately). See Figure 3.  
2.  
3.  
Slide the Battery Cover (8) off the Battery Case (11).  
The Battery Case (11) is inside the Rear Housing (7).  
CAUTION: The housing and other machined parts of this item may have sharp  
burrs that can cut you. Use care when changing the batteries.  
Carefully remove the Batteries (9) from the Battery Case (11).  
4.  
5.  
If present, remove old batteries and dispose of or recycle them properly.  
Carefully place two new “AA” Batteries (9) into the Battery Case (11). Be sure that the  
polarities (+ or -) of the batteries line up with the polarity signs.  
6.  
7.  
Carefully replace the Battery Cover (8). Insert the Battery Cover Screws (5) and tighten  
them with the screwdriver.  
Check LED light. If it does not light, repeat the steps or replace the batteries with new  
ones.  
SKU 95153  
For technical questions, please call 1-800-444-3353  
Page 5  
 
INSTAllATION  
1.  
Chose a wall or ceiling location that allows you to mount the unit onto a solid surface  
capable of sustaining the weight of the unit. If you cannot mount to wall studs, you  
will need to use the Dry Wall Mounting Anchors and Wood Screws (10). Be aware, the  
Camera needs to be mounted securely so it will not fall off the mounting and cause  
personal injury or property damage.  
Note: The mounting holes on the Outdoor Camera are approximately 1/4” or 6 mm.  
Mounting Holes  
Wall Bracket (1)  
FIgURE 4  
2.  
3.  
Hold the Wall Bracket (1) of the assembly against the surface you wish to mount. Using  
a pencil (not included), draw dots of the mounting holes. See Figure 4.  
Warning: Check that there are no hidden wires, cables or other obstructions in the  
mounting location. Predrill the holes.  
4.  
5.  
Install the drywall anchors into the holes if mounting into drywall.  
Line up the holes in the mounting bracket with the holes in the wall and hold the unit  
in place. Mount using the Wood Screws (10).  
MAINTENANCE  
Keep the Imitation camera clean and free of spider webs.  
SKU 95153  
For technical questions, please call 1-800-444-3353  
Page 6  
 
pARTS lIST  
pART #  
DESCRIpTION  
QTy.  
1
2
Wall Bracket  
1
Camera Stand  
Camera Housing  
Coaxial Wire  
1
3
1
4
1
5
Battery Cover Screw (not shown)  
Sun-Visor  
2
6
1
7
Rear Housing  
1
1
8
Battery Cover (not shown)  
“AA” Battery (not included)  
Drywall Anchor and Wood Screw  
Battery Case (not shown)  
9
2
10  
11  
3 ea.  
1
pARTS DESCRIpTION  
6
5
3
8
pivoting Screw  
11  
7
Adjustable  
Screw  
2
4
1
10  
Note: Some parts are listed and shown for illustration purposes only, and are not available  
individually as replacement parts.  
plEASE READ ThE FOllOWINg CAREFUlly  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS MANUAL  
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY  
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO  
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS  
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT  
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED  
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING  
OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,  
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
SKU 95153  
For technical questions, please call 1-800-444-3353  
Page 7  
 

Graco Camping Equipment 334644A User Manual
Graham Field Photo Scanner 9000APS User Manual
Grizzly Sander P9933021 User Manual
HANNspree Computer Monitor MAF 001003 User Manual
Harbor Freight Tools Automobile Parts 96500 User Manual
Harbor Freight Tools Fryer 44707 User Manual
Harman Kardon GPS Receiver 174 User Manual
Harman Kardon Stereo System HK3490 User Manual
Heat Controller Air Conditioner SMA 18 User Manual
HP Hewlett Packard Network Card F1381A User Manual