Harbor Freight Tools Cordless Drill 96300 User Manual

Planishing hammer stand  
For use with sKu 94847 Planishing hammer  
model 96300  
assembly and oPeration instructions  
Please note: Planishing Hammer not included with  
Stand.  
Due to continuing improvements, actual product may  
differ slightly from the product described herein.  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
to PreVent serious injury, read and understand  
all warnings and instructions beFore use.  
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
For technical questions or replacement parts, please call 1-800-444-3353.  
cover revised 07f  
 
7.  
8.  
do not force the product. use the correct product for your application. The  
correct product will do the job better and safer at the rate for which it is designed. Do  
not force the product and do not use it for a purpose for which it is not intended.  
store an idle Planishing hammer stand out of reach of children and other  
untrained persons.  
9.  
maintain this product with care.  
10.  
use only accessories that are recommended by the manufacturer for your  
model. Accessories that may be suitable for one product may become hazardous  
when used on another product.  
11.  
12.  
maintain labels and nameplates on the Planishing hammer stand. These carry  
important information. If unreadable or missing, contact Harbor Freight Tools for a  
replacement.  
maintain a safe working environment. Make sure there is adequate surrounding  
workspace. Do not use this product in a damp or wet location.  
13.  
14.  
do not use to support any items other than sKu 94847, Planishing hammer.  
use on a at, level surface capable of supporting the Planishing hammer  
stand, the Planishing hammer, the metal being worked on, and the vibration  
of the planishing process.  
15.  
16.  
do not use this Planishing hammer stand as a stepping stool or ladder. Never  
sit, stand, or climb on this Planishing Hammer Stand. Never allow children to play  
on or climb on this Stand.  
only ll the Planishing hammer stand with sand.  
assembly instructions  
note: For additional information regarding the parts listed in the following pages, refer to  
the Assembly Diagram on page 7.  
1.  
Connect Main Support (3) to Table Support (2). Insert two Bolts (6) with Washers  
(10) down through the Table Support (2) and Main Support (3). Slide on two more  
Washers (10), Spring Washers (9) and thread on the Nuts (7).  
SKU 96300  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
Figure 1  
Table Support (2)  
Leg (1)  
Spring Washers (9) and  
Nuts (7) (not visible)  
Bolts (4), Washers (10)  
2.  
3.  
Attach Table Support (2) to Leg (1). Insert two Bolts (4) with Washers (10) down  
through the Table Support (2) and down through the Leg (1). Slide on two more  
Washers (10), Spring Washers (9) and thread on the Nuts (7) - see Figure 1.  
Secure Cross Bar (8) to both the Main Support (3) and Leg (1). Slide SpringWasher  
(9) and Washer (10) onto Bolt (5). Thread in through Main Support (3) and into  
Cross Bar (8). From the opposite side, slide Spring Washer (9) and Washer (10)  
onto second Bolt (5) and thread into Leg (1) and into Cross Bar (8).  
4.  
5.  
Tighten all hardware.  
Check the Planishing Hammer Stand to make certain that it sits evenly, fully resting  
on the ground. Make certain that all hardware is fully tightened.  
Figure 2  
Main Support (3)  
Plug (11)  
6.  
7.  
Unscrew and remove both Plugs (11)-see Figure 2-and fill the Stand with sand to  
reduce noise when using the Planishing Hammer. Only use sand to fill the Stand.  
do not use any other material or any liquid to ll the stand. Screw the Plugs  
back onto the Stand.  
Place the Planishing Hammer on top of the Stand and align the mounting holes of  
both Stand and Planishing Hammer. Position the operating portion of the planishing  
hammer above the Leg (1) of the stand as shown on the cover picture.  
reV 07f  
SKU 96300  
For technical questions, please call 1-800-444-3353.  
Page 4  
 
8.  
9.  
Secure Planishing Hammer to the Planishing Hammer Stand by sliding a grade-5  
bolt (not included) of adequate length through a flat washer (not included), then  
through the base hole of the Planishing Hammer, and then through the mounting  
plate of the Stand. Slide another flat washer (not included) over the bolt. Attach a  
self-locking nut (not included). Repeat this operation for the remaining mounting  
holes. Then tighten all the nuts.  
The Planishing Hammer Stand has three 7/16” holes for mounting the Stand to your  
work surface (hardware not included). use on a at, level surface capable of  
supporting the Planishing hammer stand, the Planishing hammer, the metal  
being worked on, and the vibration of the planishing process.  
insPection, maintenance, and cleaning  
1.  
2.  
Clean the Planishing Hammer Stand with a damp cloth. Do not use abrasives,  
harsh chemicals or detergents as these will scratch and damage the Planishing  
Hammer Stand.  
beFore each use, inspect the general condition of the Planishing Hammer  
Stand. Check for loose fasteners, cracked or broken parts and any other condition  
that may affect its safe operation. Always make sure the Planer is firmly attached  
to the Stand. do not use damaged equipment.  
Parts list  
Part  
description  
Q’ty  
Part  
7
description  
Q’ty  
4
1
2
3
4
5
6
Leg  
1
1
1
2
2
2
Nut M8  
Table Support  
8
Cross Bar  
Spring Washer  
Flat Washer  
Plug  
1
Main Support  
9
6
Bolt M 8 x 50mm  
Bolt M8 x 75mm  
Bolt M8 x 20mm  
10  
11  
10  
2
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROvIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS  
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESEN-  
TATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE  
PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANU-  
FACTURER AND/OR DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE  
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL  
RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS  
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
SKU 96300  
For technical questions, please call 1-800-444-3353.  
Page 5  
 
assembly and Parts diagram  
11  
11  
SKU 96300  
For technical questions, please call 1-800-444-3353.  
Page 6  
 
limited 1year warranty  
Harbor Freight Tools Co. makes every effort to assure that its products meet high  
quality and durability standards, and warrants to the original purchaser that this product is  
free from defects in materials and workmanship for the period of one year from the date of  
purchase (90 days if used by a professional contractor or if used as rental equipment).This  
warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence  
or accidents, repairs or alterations outside our facilities, normal wear and tear, or to lack  
of maintenance.We shall in no event be liable for death, injuries to persons or property, or  
for incidental, contingent, special or consequential damages arising from the use of our  
product. Some states do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitation of exclusion may not apply to you.THIS WARRANTY IS  
ExPRESSLY IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUD-  
ING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.  
To take advantage of this warranty, the product or part must be returned to us with  
transportation charges prepaid. Proof of purchase date and an explanation of the com-  
plaint must accompany the merchandise. If our inspection verifies the defect, we will either  
repair or replace the product at our election or we may elect to refund the purchase price  
if we cannot readily and quickly provide you with a replacement. We will return repaired  
products at our expense, but if we determine there is no defect, or that the defect resulted  
from causes not within the scope of our warranty, then you must bear the cost of returning  
the product.  
This warranty gives you specific legal rights and you may also have other rights  
which vary from state to state.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
SKU 96300  
For technical questions, please call 1-800-444-3353.  
Page 7  
 

Grundig Flat Panel Television 46 VLE 8160 BL User Manual
Hayter Mowers Lawn Mower 446 Hovertrim User Manual
Healthrider Home Gym HRCCEL49011 User Manual
Heath Zenith Home Safety Product SH 5512 User Manual
Honeywell Model Vehicle AP 010BT User Manual
Hotpoint Oven Accessories CH60DPCF S User Manual
Hotpoint Washer HULT 963 User Manual
HP Hewlett Packard Camera Accessories Media Vault User Manual
Hubbell Work Light SZ 32 User Manual
IBM Laptop 4693 DBCS FAMILY User Manual