Harbor Freight Tools Air Cleaner 43242 User Manual

Model 43242  
MINI AIR FILTER  
With Pressure Gauge and Pressure Regulator  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright © 2000 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork  
contained herein may be reproduced in any shape or form without the express  
written consent of Harbor Freight Tools.  
For technical questions please call 1-800-444-3353  
UNPACKING  
FIGURE A  
When unpacking, check to make sure all parts shown on the back of this instruction  
sheet are included. If any parts are missing or broken, please call Harbor Freight Tools  
at the number shown on the front of this instruction sheet as soon as possible.  
1
22  
OPERATING INSTRUCTIONS  
NOTE:All parts mentioned below refer to parts shown on the reverse side of this  
instruction sheet.  
23  
1. For ease of use, and to avoid damage to the Mini Air Filter, it is recommended that the unit be  
mounted in a convenient location on the workbench or in the work area. This can be done by  
attaching the Mounting Bracket (part #22) to the side of the workbench or wall, using two  
wood or metal screws (not provided). (Figure A)  
AIR OUT-  
LET  
2. Once the Mounting Bracket has been attached to a desired location, unscrew and remove the  
Retaining Ring (part #23) from the top of the Mini Air Filter.  
3. Insert the top of the Mini Air Filter through the Mounting Bracket and secure by replacing the  
Retaining Ring.  
11  
9
4. Attach a 1/4” NPT Female hose connector to the air compressor supply hose. Then, wrap the  
threads of the 1/4” NPT Female hose connector with approximately 3” of Teflon tape. Next,  
connect the 1/4” NPT Female hose connector to the inlet side of the Mini Air Filter.  
5. Attach a 1/4” NPT Male hose connector to one end of the outlet extension hose (to which you  
will connect a tool). Check to make sure the other end of the outlet extension hose is fitted  
with a quick coupler. Then, wrap the threads of the 1/4” NPT Male hose connector with  
approximately 3” of Teflon tape. Next, connect the 1/4” NPT Male hose connector to the outlet  
side of the Mini Air Filter.  
14  
6. Connect the quick coupler of the air outlet extension hose to the tool you are using. Turn on  
the air compressor and regulate the desired PSI to the tool by pulling up and turning the  
Pressure Adjustment Knob (part #1) on the Mini Air Filter clockwise for reduced air pressure,  
or counterclockwise for increased air pressure. Press down on the knob to lock.  
7. The Mini Air Filter is now ready for use. NOTE: Depending on usage, periodically examine  
the Drain Cup (part #11) for accumulated water that is being separated from the compressed  
air system. See Step one for instructions on draining the excess fluid from the Drain Cup.  
CLEANING AND MAINTENANCE  
1. When the water level rises to the bottom edge of the  
Filter Mesh Mounting (part #9) within the Drain Cup (part  
#11) it is necessary to remove the excess fluid. To drain  
the fluid slowly turn the Water Valve Drain (part #14)  
counterclockwise until the fluid begins to flow from the  
Drain Cup. When all of the fluid has been drained turn  
the Water Valve Drain clockwise to tighten.  
SEE REVERSE SIDE OF THIS INSTRUCTION FLYER FOR PRODUCT  
WARNINGS, PRECAUTIONS, PARTS LIST, AND ASSEMBLY DIAGRAM.  
2. To clean, wipe with a clean, damp cloth, using a mild  
soap with water if necessary. Then, dry.  
REV 01d; 07g  
 

Graco Baby Swing PD225586A User Manual
GSW Water Heater Electric Water Heate User Manual
Hamilton Beach Coffeemaker 840153800 User Manual
HANNspree Flat Panel Television ST49 User Manual
Harbor Freight Tools Fish Finder 96902 User Manual
HP Hewlett Packard All in One Printer 5SI User Manual
HP Hewlett Packard Graphics Tablet HP 61016A User Manual
HP Hewlett Packard Landscape Lighting 419A User Manual
HP Hewlett Packard Personal Computer A2W63UT User Manual
Husqvarna Chainsaw 1100 CD User Manual