Haier Washer XPB60 287S User Manual

Twin-tub Washing Machine  
User manual  
This manual is for  
XPB60-287S  
Please read this manual  
carefully before using.  
Retain it for DfuotwunrleoardefrfoemreWnwcwe..Somanuals.com. All Manuals Search And Download.  
Parts and features  
Water inlet  
Water filling switch  
Drain hose hook  
Lint filter  
(Installed by user)  
Power cord  
Meaning and description of the symbols  
Contents marked with this symbol are related  
to the safety of the product and the personal  
safety of the users. Please operate in strict  
conformity to the contents, otherwise it may  
cause damage to the machine or injure the  
personal safety of the user.  
Warning  
Contents marked with this symbol are actions  
forbidden to perform. Performing of those  
actions may result in damage to the machine  
or injure the personal safety of the user.  
Forbidden  
Please check that the power supply has good earthing connection  
condition before using to guarantee your safety.  
1
 
Important safety instructions  
Important!  
Warning - to reduce the risk of fire, electric shock, or injury when using your  
appliance, follow basic precautions, including the following:  
Read all instructions before using the appliance.  
This appliance isnot intended foruse by persons(including children) with  
reduced physical, sensory or mental capabilities, or lack of experience and  
knowledge, unless they have been given supervision or instruction concerning  
use of theappliance by aperson responsible fortheir safety.  
Children should be supervised to ensure that they do not play with the  
appliance.  
If the supplycord is damaged, it must bereplaced by themanufacturer, its  
service agent or similarly qualified persons in order to avoid a hazard.  
This appliance must be properly installed in accordance with the installation  
instructions before it is used.  
Never unplug your appliance by pulling on the power cord. Always grasp the  
plug firmly andpull straight out from the outlet.  
Replace worn power cords, loose plugs/power outlets immediately. The power  
cord must be replaced by an Authorised repairer.  
Unplug your appliancebefore cleaning orbefore making anyrepairs.  
Do not operateyour appliance inthe presence ofexplosive fumes.  
Do not use hot water that exceeds 65 C.  
Do not use this appliance to wash clothes soaked, spotted or washed in petrol,  
dry cleaning solvents, or any other explosive or flammable substances that  
could ignite and explode.  
Clothes or rags used to clean flammable or explosive materials should not be  
washed in this appliance until all traces of this material has been removed.  
Do not add or mix any flammable or explosive substances to the wash.  
Do not try to remove clotheswhile the tubis moving. Let it come toa  
complete stop.  
The lid must be closed when the bowl is spinning.  
Do not operate your appliance when parts are missing or parts are broken.  
Do not use this appliance for commercial clothes washing.  
Do not operate this appliance unless all enclosure panels are properly in place.  
Do not tamperwith the controls.  
To reduce risk ofinjury do notallow children toplay with theappliance. Close  
supervision of children is necessary when the appliance is used near children.  
This appliance mustbe connected to a proper electricaloutlet socket withthe  
correct electrical supply.  
Do not repair or replace any part of the appliance or attempt any servicing  
unless specifically recommended in the user-repair instructions that you  
understand and haveskills to carryout.  
To reduce the risk of electric shock or fire, do not use extension cords or  
adapters to connect the unit to an electrical power source.  
SAVE THESE INSTRUCTIONS  
2
 
Installation  
Please install and adjust the machine in accordance with this manual. It  
is very important for your safety and for the correct operating of your  
machine.  
Install the lint filter  
After opening the package , please take out the lint  
filter from the bag , install it to the overflow  
filter of the wash tub. See the figure.  
Overflow filter  
Lint filter  
Connecting the hoses & Selecting the water level  
Use the new hose-sets supplied with the appliance. Do not use  
old hose sets from your previous appliances.  
Connect the water inlet hose into the water inlet on the  
control panel.  
Water inlet hose  
Water inlet  
Select water level suitable to  
the quantity of the laundry.  
Set the water level indicator  
to a suitable level.  
Water level  
indicator  
The temperature of water  
must be under 60 C.  
Maximum Max  
Med  
Medium  
Min  
Minimum  
Set up the drain hose  
Before using, hang the drain hose  
in a suitable location.  
0.8  
H
1.2m  
The height of the drain hose should be between  
0.8-1.2m .  
3
 
Installation  
How to change the direction of the drain hose  
Figure 1 indicates the ex factory  
installation position of the drain hose.  
Back  
Front  
Soft cloth  
Extend the drain hose from the side of the spin tub  
Figure 1  
Put a soft cloth on the ground. Lean  
the machine down gently with the  
front surface facing the ground.  
Unhook the drain hose from the  
cabinet. Take the hose out of the  
Soft cloth  
fixing groove.(See to Figure 2).  
Figure 2  
Place the drain hose into the groove  
along the side of the spin tub in the  
direction of (1)~(3), towards the side  
of the spin tub. (See to Figure 3).  
Extend to the  
spin tub side  
Embed into the  
groove in turn  
Place the drain hose into the  
groove by hand. Take care not  
to damage the drain hose in  
fastening the fixing clamp.  
Figure 3  
Extend the drain hose from the rear  
Take out the drain hose from the fixing groove. Extend it from the  
rear as per the direction of the arrow. (When the drain hose  
is extended from the rear, it can  
be hung on either side of the  
cabinet.)(See to Figure 4).  
Figure 4  
4
 
Preparation before washing  
Positioning your washer  
1.Connect the water inlet hose.  
2.Select a suitable location for the washer on a hard,  
even surface away from direct sunlight or heat  
sources, e.g radiators, cooking appliances etc.  
3.The washer must not be placed in an area where  
the temperature is below freezing point.  
0.8m  
H
1.2m  
4.Any floor unevenness may result in unstable  
working or abnormal noise. Please ensure  
the machine is level.  
Check the following before washing  
The weight of  
the laundry  
shall not  
exceed the  
rated capacity.  
Loosen the  
laundry before  
placing it  
When the machine  
is running buttons  
may cause noise.  
To reduce the noise  
turn clothes inside  
out or place them  
in a laundry bag.  
Check if the Clear the  
laundry has pockets.  
any special Take out loose  
washing  
items such  
instructions. as coins, sand,  
hairpins etc.  
Tie any  
long strips,  
fasten  
buttons  
and close  
zippers.  
evenly in the  
tub.  
a. Check if the laundry is suitable for machine washing.  
b. Divide the laundry into colour fast and non-colour fast items.  
c. Place items that do not absorb water easily into the water by hand.  
d. For heavily soiled items, please first remove loose dirt, then apply  
detergent directly to the stain before washing.  
e. For those items that may get lint or are furry or fluffy, please turn  
them inside out before washing  
f . Do not put laundry polluted by chemicals into the washing machine.  
5
 
Cautions  
The rated washing/spinning capacity  
refers to the largest dry weight of a load  
that can be washed/spun.  
The thickness, size and type of clothes  
will influence the actual capacity. Be  
careful to only load a reasonable amount  
of laundry.  
Do not select "Maximum" water level for  
clothes less than 2.4kg, to avoid splashing  
of water.  
It is suggested not to use high sudsing  
detergent. Choose a low suds or high  
efficiency detergent.  
Usage of the detergent  
How to use whitener  
Adding the washing powder  
Dissolve in the machine:  
1.Fill small quantity of water.  
2.Add the powder. Run for 30  
seconds to dissolve it completely.  
3.Put in the laundry. Select a  
suitable water level.  
Instant dissolving of the washing  
powder:  
Fill water to desired level.  
Dilute the whitener in a  
container. Pour it slowly  
into the washing tub.  
Avoid using whitener on  
laundry with color or  
pattern as they are prone  
to lose color.  
The whitener shall not  
touch the laundry  
directly.  
1.Prepare warm water of 30 C in a  
container.  
2.Add the powder while stirring to fully  
dissolve it.  
Powder is more likely to contaminate  
the laundry with residue than a liquid  
detergent. Therefore please use the  
correct quantity.  
Please refer to the washing powder  
instructions for the correct use and  
dosage.  
Refer to the whitener  
instructions for the  
usage and quantity.  
For powder whitener,  
please dissolve it before  
using.  
6
 
Washing sequence  
Wash timer  
Wash selector  
(Delicate, normal,  
Drain)  
Spin timer  
(To set to below 2 minutes,  
(to set to below 1 minute,  
first set to 2 minutes then  
turn it back. This can increase  
the service life of the timer.)  
first set to  
6
minutes then  
Water inlet  
turn it back. This can increase  
the service life of the timer.)  
NORMAL  
OFF  
OFF  
DELICATE  
DRAIN  
WASH SELECTOR  
WASH TIMER  
SPIN TIMER  
Wash  
WASH SPIN  
1.Water-filling selector  
Set the water inlet selector to the "WASH" side.  
(Figure 1)  
2.Fill with water to the set level and add the  
dissolved washing powder. (Figure 2)  
3.Place the clothes into the water.  
Figure 2  
NORMAL  
4.Select the wash mode, either "delicate"  
or "normal". (Figure 3)  
DELICATE  
DRAIN  
5.Select the washing time  
WASH SELECTOR  
Figure 3  
Select the washing time according to the load  
size and how dirty the clothes are. (Figure 4)  
Note: For a full load on the normal cycle first  
wash for 3 minutes, the clothes will absorb  
the water. At the end of 3 minutes add extra  
water up to the maximum water level mark.  
Then wash for a further 15 minutes using  
the wash timer.  
OFF  
WASH TIMER  
Figure 4  
Figure 5  
NORMAL  
DELICATE  
DRAIN  
6.After washing, set the "WASH  
SELECTOR" at "DRAIN". (Figure 5).  
WASH SELECTOR  
Energy test program 18 min Normal Warm Wash (35'C), 9 min Rinse, 5 min spin (1/2 load).  
Add the clothes load. Fill the wash tub to the maximum water level. Water at 35'C.  
While it is filling (half) add the detergent/PBIS mixed with 1 litre of Min.35'C water.  
Wash on "normal" for 3 minutes. Then fill the wash tub again to the maximum water level. Water at 35'C.  
Wash on "normal" for 15 minutes. Drain for 5 minutes. Divide load into two halves.  
Spin each half load for 5 minutes. Place the clothes in the wash tub and then fill with cold  
(20'C) water to the maximum level.  
Wash/rinse for 9 minutes. Drain for 5 minutes.  
Divide load into two halves. Spin each half load for 5 minutes. Program end.  
Detergent : drum type .  
For best results , we recommend mixing detergent with warm water ,and using max anti-foam .  
7
 
Additional spinning  
Additional spinning  
If you want to remove more foam, you can use this function.  
1.Put the clothes into the spin tub evenly.  
2.Spin  
(1) Put the retainer in properly.  
Please use the retainer even if the  
clothes quantity is small.  
Push retainer down  
Push  
Correct  
The laundry  
is slanting  
(2) Close the inner and outer cover of the spin tub.  
Correct  
No retainer  
Outer cover of  
The spin tub  
Inner cover of  
The spin tub  
(3) Spin for 1-2 minutes.  
3.To remove foam during spinning.  
(1) Open the outer cover of the spin tub.  
(2) Set the water-filling selector control  
rod to the "SPIN" side. Fill water for  
about 1 minute.  
WASH SPIN  
If the water flow is too fast, the water  
may flow out from the wash tub side.  
You may turn the water tap down to  
limit the flow of water.  
(3) Close the outer cover of the spin tub.  
Spin for 1-2 minutes.  
8
 
Rinsing  
Rinsing  
1. Put the clothes into the wash tub. Select suitable mode  
according to the clothes load.  
2.Adjust the water level  
Set the water level using the water level adjusting  
lever according to the clothes quantity. Then fill.  
3.Rinse  
Adjust the wash timer to a suitable rinse length.  
Use 9 minutes for a full wash. A partial wash  
load may only require 5-7 minutes.  
Spinning  
Spinning  
1. Put the clothes into the spin  
Spin time  
tub evenly and smoothly.  
Spin Time  
(minutes)  
Note that a full wash load will  
need to be split into two equal  
loads for spinning.  
Clothes  
Normal full load,  
bed sheet  
or blanket  
About 4~5  
2. Press the retainer into the tub  
properly. Close the inner and  
outer cover of the spin tub.  
Underwear  
(knitwear)  
About 2~4  
About 1~2  
Sweater  
(synthetic fiber)  
3. Spin  
Set the WASH TIMER at  
OFF and WASH  
Mixed  
light loads  
Within 1 minute  
SELECTOR at DRAIN  
Spin a full load.  
.
During spinning, spinning will stop if the outer cover of the spin tub  
is opened. Close the cover to continue spinning.  
If you want to fill water during spinning to remove the foam, we  
recommend spinning the laundry first for about 1 minute, then  
add water to the spin tub. Otherwise the spinning will stop  
because of too much water.  
9
 
Care and cleaning  
Please first pull out the power plug from the electrical supply  
before cleaning.  
Cleaning the lint filter  
The lint filter must be used during washing.  
It must be cleaned after each wash.  
1. Remove the lint filter  
Put hand at the indicated position.  
Push down to take it off. ( See  
Figure 1)  
Figure 1  
2. Clean the lint filter  
Put it in water and clean while it is  
still wet.(See Figure 2)  
Figure 2  
3. Install the lint filter  
After cleaning, insert the bottom  
of the lint filter ( marked with  
"down side") into the overflow filter ,  
then push the upper part of the  
filter in ( marked with " up side ").  
(See Figure 3)  
Figure 3  
10  
 
Care and cleaning  
Cleaning the overflow filter  
Too much lint on the overflow filter will influence  
the normal usage of the machine. Please  
clean it every two months.  
1
Take off the overflow filter.  
As indicated in the figure, squeeze  
the elastic fixing claw and pull it in  
Elastic fixing  
claw  
the direction of the arrow .  
(See to Figure 1)  
Figure 1  
2. Remove the corrugated pipe.  
Dismantle the upper part of the  
corrugated pipe inside the  
overflow filter ( as indicated in  
Figure 2).  
Water level  
adjusting lever  
Corrugated  
Pipe  
3. Cleaning the overflow filter  
Clean the lint around the filter  
and flush with tap water.  
Figure 2  
4. Install the overflow filter.  
(1).Install the corrugated pipe.  
(2).Insert the mounting plate at  
the bottom of the filter into  
the valve cover.  
Hook  
(3).Hang up the hook at the left  
upper side.  
(4).Push the upper part in as  
indicated in Figure 3.  
Figure 3  
11  
 
Care and cleaning  
Clean the cabinet  
Use only a damp cloth for cleaning the control panel.  
To avoid any kind of damage to cabinet finish, use a  
small amount of liquid dishwashing detergent with  
warm water to wipe the washer cabinet as required.  
Petrol  
Thinner  
Alcohol  
If fabric softener, bleach or detergent is accidently spilt on the  
cabinet, wipe the cabinet immediately.  
Do not use any abrasive, harsh chemicals, ammonia, chlorine  
bleach, concentrated detergent, solvents or metal scouring pads.  
Some of these chemicals may dissolve, damage and/or discolour  
your washer.  
Leave the lid open after completing the wash cycle to allow the  
inside of the washer to dry out and prevent bad odours from forming.  
Transporting or storing your washer  
Drain any water from the inlet hoses.  
Disconnect the power cord from the electrical supply.  
Dry out the inner wash bowl and, if putting the machine into  
storage or going on holiday, leave the lid open or propped ajar to  
allow air to circulate.  
If moving the washer, disconnect the drain hose.  
Always transport or store your washer in an upright position only.  
The washer must be stored at room temperature.  
Trouble-shooting  
If clothes fall to the outer side of the spin tub  
If clothes fall to the outer side of the spin tub, please contact an  
authorised service agent. Do not repair it yourself.  
12  
 
Trouble-shooting  
When the remaining water is frozen  
To prevent freezing drain after using.  
After complete draining, set the "WASH SELECTOR" at "STRONG"  
or "STANDARD". If it is set at "DRAIN", it will be more difficult for  
the frozen water to melt.  
When the water is frozen  
Below 50 c  
2~3L  
Pour warm water below 50 into the  
wash tub. After several minutes,  
turn the pulsator on gently. Please  
ensure the drain is working normally  
before using again.  
(Always unplug your washer to avoid an electrical shock before checking)  
The following problems may not require a service call. Please confirm the  
fault before calling an Authorised Service Agent. Do not repair it yourself.  
Operating problems  
The reasons  
Is there power failure?  
Is the power plug loose?  
Is the pulsator blocked?  
The machine does  
not start.  
Is the drain hose blocked ?  
Check the position of the drain hose, make  
sure that the drain hose is fitted into a tub or  
drain standpipe 0.8-1.2m above the floor.  
Water will not drain  
Coins, loose change, or buttons could cause  
noises if caught in the wash.  
There's abnormal  
sound during washing  
Is the machine placed on a flat floor?  
Is the retainer in the spin tub pressed evenly?  
Is the amount of laundry in spin tub too much?  
There's abnormal  
sound and violent  
vibration during  
spinning  
Water left in the drain  
hose when first use  
of the machine.  
It is the water remaining from the factory  
inspection of performance.  
13  
 
Accessories supplied  
Name  
Quantity  
User's manual  
One piece  
One piece  
Warranty manual  
Water inlet hose  
One piece  
Lint filter  
One piece  
One piece  
Retainer  
Specification  
Maximum/41L Medium/36L  
Minimum/30L  
Water level/Water quantity (about)  
Water pressure(MPa)  
0.02-0.2  
Rated washing / spinning capacity(kg)  
6.0/3.0 (weight of standard dry clothes)  
14  
 

Graco Car Seat PD209997A User Manual
Grindmaster Coffeemaker P200 User Manual
Haier Flat Panel Television 43E4500R User Manual
Harbor Freight Tools Indoor Fireplace 91797 User Manual
Harbor Freight Tools Lathe 46407 User Manual
Honeywell Thermostat CM901 User Manual
Hotpoint Refrigerator FF50 User Manual
HP Hewlett Packard Network Router B User Manual
Hypertec Carrying Case N19648NHY User Manual
iHome Clock iH41 User Manual