Harbor Freight Tools 66552 User Manual

Motocross dirt bike stand  
66552  
set up and operating instructions  
®
distributed exclusively by Harbor Freight tools .  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
read this material before using this product.  
Failure to do so can result in serious injury.  
saVe tHis Manual.  
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork  
contained herein may be reproduced in any shape or form without the express written consent of  
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing  
improvements, actual product may differ slightly from the product described herein. Tools required for  
assembly and service may not be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
c.do not overreach. keep proper  
footing and balance at all times.  
This enables better control of the tool  
in unexpected situations.  
11. Keep out of reach of children.  
12. Maintain labels and nameplates on  
the tool. These carry important safety  
information. If unreadable or miss-  
ing, contact Harbor Freight Tools for a  
replacement.  
d.dress properly. do not wear loose  
clothing or jewelry. keep your  
hair, clothing and gloves away  
from moving parts. Loose clothes,  
jewelry or long hair can be caught in  
moving parts.  
13. The warnings, precautions, and in-  
structions discussed in this instruction  
manual cannot cover all possible con-  
ditions and situations that may occur.  
It must be understood by the operator  
that common sense and caution are  
factors which cannot be built into this  
product, but must be supplied by the  
operator.  
e.only use safety equipment that  
has been approved by an appropri-  
ate standards agency. Unapproved  
safety equipment may not provide  
adequate protection. Eye protection  
must be ANSI-approved and breath-  
ing protection must be NIOSH-ap-  
proved for the specific hazards in the  
work area.  
saVe tHese  
instructions.  
Motocross bike stand  
safety Warnings  
1. Strap load to Saddle before lifting.  
2. Keep clear of Release Bar and do not  
leave unattended while supporting  
load.  
3. Do not exceed 350 lb. capacity.  
4. Center load on Saddle.  
5. Raise and lower using second person  
to stabilize load.  
6. Keep out from under load while low-  
ering.  
7. Inspect before every use; do not use  
if parts are loose or damaged.  
8. Use as intended only.  
9. Operate on flat and level surface.  
10. Do not rock load on Stand.  
SKU 66552  
For technical questions, please call 1-800-444-3353.  
Page 3  
U-Shaped  
Bracket  
speciFications  
Pedal  
Weight Capacity  
350 lb.  
unpacking  
Long  
Bolt  
When unpacking, make sure that the  
item is intact and undamaged. If any parts  
are missing or broken, please call Harbor  
Freight Tools at the number shown on the  
cover of this manual as soon as possible.  
2. Insert Long Bolt (6) through:  
Washer (9);  
One hole in U-shaped Bracket un-  
der Saddle (1);  
Bushing (10);  
asseMblY  
Hole in end of Pedal (3);  
Bushing (10);  
read the entire iMportant  
saFetY inForMation  
section at the beginning of this  
manual including all text under  
subheadings therein before set  
up or use of this product.  
Other hole in U-shaped Bracket;  
Washer (9).  
3. Secure Long Bolt  
with a Lock Nut (8).  
note: For additional information regarding  
the parts listed in the following pages,  
refer to the Assembly Diagram near  
the end of this manual.  
4. Insert Short Bolt (7) through:  
Washer (9);  
Mounting Bracket (5);  
Washer (9);  
1. Make sure rubber end caps are se-  
cured into feet of Base (2).  
Remaining hole in Pedal (3);  
Washer (9);  
Remaining Mounting Bracket (5);  
Washer (9).  
5. Secure Short Bolt with a Lock Nut (8).  
Steps 4 and 5  
6. Insert remaining Short Bolt (7)  
through:  
Washer (9);  
Steps 6 and 7  
Steps 2 and 3  
Release Bar (4);  
Washer (9);  
Remaining hole in Mounting Brack-  
et (5);  
Washer (9);  
SKU 66552  
For technical questions, please call 1-800-444-3353.  
Page 4  
Hole in foot on Base (2);  
locking  
pin (11)  
Washer (9);  
Remaining hole in second Mounting  
Bracket (5);  
Washer (9).  
7. Secure Short Bolt with Lock Nut (8).  
8. Before using the Bike Stand with a  
load, test the operation of the Pedal  
and Release Bar, without any load,  
following the operating instructions  
below.  
r-pin  
(12)  
4. Insert Locking Pin (11) fully through  
the hole in the saddle and the base  
to secure the stand in the up position.  
Lock it in place with the R-Pin (12)  
operating instructions  
read the entire iMportant  
saFetY inForMation  
section at the beginning of this  
manual including all text under  
subheadings therein before set  
up or use of this product.  
5.  
Warning! stay clear of release  
bar while saddle is elevated and in  
use.  
6. Remove tools from under stand be-  
fore lowering.  
1. Locate Stand on hard, flat, and level  
surface able to withstand load without  
deforming.  
7. To lower Saddle, keep clear and  
remove the R-Pin and Locking Pin.  
Place foot on Release Bar and Pedal.  
Using second person to stabilize  
load, press on Release bar while  
guiding Pedal up to smoothly lower  
Saddle.  
2. Center dirt bike over Saddle and se-  
cure to saddle with tie-down strap  
(sold separately) before lifting.  
3. Using second person to stabilize  
load, slowly raise Saddle by de-  
pressing Pedal with your foot until  
Saddle is fully raised.  
SKU 66552  
For technical questions, please call 1-800-444-3353.  
Page 5  
please read tHe FolloWing  
Maintenance and  
serVicing  
careFullY  
THe MANUFACTUReR AND/OR DISTRIBUTOR  
HAS PROvIDeD THe PARTS LIST AND  
Procedures not specifically  
explained in this manual  
must be performed only by a  
qualified technician.  
ASSeMBLy DIAgRAM IN THIS MANUAL AS  
A ReFeReNCe TOOL ONLy. NeITHeR THe  
MANUFACTUReR OR DISTRIBUTOR MAKeS  
ANy RePReSeNTATION OR WARRANTy OF  
ANy KIND TO THe BUyeR THAT He OR SHe  
IS qUALIFIeD TO MAKe ANy RePAIRS TO THe  
PRODUCT, OR THAT He OR SHe IS qUALIFIeD  
TO RePLACe ANy PARTS OF THe PRODUCT.  
IN FACT, THe MANUFACTUReR AND/OR  
DISTRIBUTOR exPReSSLy STATeS THAT  
ALL RePAIRS AND PARTS RePLACeMeNTS  
SHOULD Be UNDeRTAKeN By CeRTIFIeD  
AND LICeNSeD TeCHNICIANS, AND NOT By  
THe BUyeR. THe BUyeR ASSUMeS ALL RISK  
AND LIABILITy ARISINg OUT OF HIS OR HeR  
RePAIRS TO THe ORIgINAL PRODUCT OR  
RePLACeMeNT PARTS THeReTO, OR ARISINg  
OUT OF HIS OR HeR INSTALLATION OF  
RePLACeMeNT PARTS THeReTO.  
to preVent  
serious injurY  
FroM tool Failure:  
do not use damaged  
equipment. if abnormal noise  
or vibration occurs, have the  
problem corrected before  
further use.  
cleaning and Maintenance  
1. beFore eacH use, inspect the  
general condition of the tool. Check  
for loose screws, misalignment or  
binding of moving parts, cracked or  
broken parts, and any other condition  
that may affect its safe operation.  
2. aFter use, clean external surfaces  
of the tool with clean cloth.  
SKU 66552  
For technical questions, please call 1-800-444-3353.  
Page 6  
parts list  
parts list  
part  
description  
Qty.  
part  
description  
M10x50 Bolt (Short Bolt  
M10 Lock Nut  
Qty.  
1
2
3
4
5
6
Saddle  
Base  
Pedal  
1
1
1
1
2
1
7
8
9
2
3
Washer  
11  
2
1
Release Bar  
Mounting Bracket  
M10x70 Bolt (Long Bolt)  
10 Bushing  
11 Locking Pin  
12 R-Pin  
1
asseMblY diagraM  
9
1
8
10  
9
8
9
8
9
5
9
2
3
9
6
9
5
9
9
9
7
9
7
4
note: Locking Pin (11) and R-Pin (12) not shown.  
record products serial number Here:  
note: If product has no serial number, record month and year of purchase instead.  
note: Some parts are listed and shown for illustration purposes only, and are not avail-  
able individually as replacement parts.  
SKU 66552  
For technical questions, please call 1-800-444-3353.  
Page 7  
liMited 90 daY WarrantY  
Harbor Freight Tools Co. makes every effort to assure that its products meet high  
quality and durability standards, and warrants to the original purchaser that this prod-  
uct is free from defects in materials and workmanship for the period of 90 days from  
the date of purchase. This warranty does not apply to damage due directly or indirectly,  
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,  
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.  
We shall in no event be liable for death, injuries to persons or property, or for incidental,  
contingent, special or consequential damages arising from the use of our product. Some  
states do not allow the exclusion or limitation of incidental or consequential damages, so  
the above limitation of exclusion may not apply to you. THIS WARRANTy IS exPReSS-  
Ly IN LIeU OF ALL OTHeR WARRANTIeS, exPReSS OR IMPLIeD, INCLUDINg THe  
WARRANTIeS OF MeRCHANTABILITy AND FITNeSS.  
To take advantage of this warranty, the product or part must be returned to us with  
transportation charges prepaid. Proof of purchase date and an explanation of the com-  
plaint must accompany the merchandise. If our inspection verifies the defect, we will ei-  
ther repair or replace the product at our election or we may elect to refund the purchase  
price if we cannot readily and quickly provide you with a replacement. We will return re-  
paired products at our expense, but if we determine there is no defect, or that the defect  
resulted from causes not within the scope of our warranty, then you must bear the cost  
of returning the product.  
This warranty gives you specific legal rights and you may also have other rights  
which vary from state to state.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
SKU 66552  
For technical questions, please call 1-800-444-3353.  
Page 8  

American Dynamics LIRC0308CS User Manual
Breville HB95 User Manual
Casio Graphing Calculator FXCG10LIH User Manual
DreamGEAR Carrying Case DGODS 4208 User Manual
Eclipse Fujitsu Ten TD508II WH User Manual
Elevation Audio DX300 4 User Manual
GE WineChiller User Manual
JBL GTO462 User Manual
JVC Camcorder GR DV3000 User Manual
JVC GET0114 001A User Manual